產品[
液壓測試管
]資料
如果您對該產品感興趣的話,可以
產品名稱:
液壓測試管
產品型號:
Fluke 700 HTH
產品展商:
美國福祿克fluke
關注指數:2433
產品文檔:
無相關文檔
咨詢電話:0512-68050030
簡單介紹
美國福祿克Fluke 700 HTH液壓測試管 配合使用：與Fluke 700HTP液壓測試泵配合使用。fluke壓力測試儀 美國福祿克壓力泵
液壓測試管
的詳細介紹
液壓測試管描述：
● 壓力高達10，000Mpa
● 長1米
隨機附件包括：
● 不銹鋼接頭接700HTP手泵
● 不銹鋼接頭接儀表
● 復合密封圈
● 尼龍密封圈
● 接頭： 1/4NPT外螺紋到1/4NTP外螺紋，1/4NPT外螺紋到1/8NTP外螺紋
● 操作指南
美國福祿克Fluke 700 PCK壓力校準套件
描述：Fluke 700PCK使那些自己有壓力標準的用戶可以自己來校準其壓力模塊
Fluke 700 ILFN內嵌式過濾器
配合使用：與Fluke713，717，718壓力校準器配合使用。
描述：使校準器的傳感器與液體隔離，它可以吸收氣體中少量的小滴液體。
● 入口接頭：1/8NPT黃銅內螺紋接頭
● 出口接頭：1/8NPT黃銅內螺紋接頭
● 壓力量程：100psi/690vkPa
● 爆破壓力：375psi/2588kPa
● 溫度：200°F/93℃
應用：Fluke-718只可以使用干的非腐蝕性的氣體，接一個Fluke-700ILF在718的壓力接口將會控制液體進入校準器，這樣就可以使718可以應用在壓力輸出源并不是完全干的場合，當發現氣體中有明顯的水珠或過濾器被大量的液體浸透時應該立即替換過濾器 Fluke 700HTP Hydraulic Test Pump
The Fluke 700HTP is designed to generate pressures up to 10,000 psi/700 bar. The Fluke 700HTP has two pressure ports:
3/8-BSP (ISO228) female parallel thread fitting for the reference gauge or pressure module
1/8-BSP (ISO228) female parallel thread fitting for the unit under test
Note: The user must provide a hose with appropriate end fittings from this port to the unit under test.
Fluke 700HTP Hydraulic Test Pump
This pump can provide up to 10,000 psi using distilled water or mineral-based hydraulic oil. The pump is operated by pumping several strokes to prime the system, then switching to high pressure mode when the resistance increases. An integral pressure adjustment vernier knob varies the pressurized volume by 0.6 cc. The pressure variation achievable with the vernier will depend on the nominal pressure and total pressurized volume, but with a minimum volume, the vernier provided 150-3,000 psi (at 150 psi nominal) and 3,000-10,000 psi (at 3,000 psi nominal) adjustment ranges. With a minimum volume and no pressure applied, the vernier can also be used to provide a 0 to 1.7 psi range. Larger volumes will provide a smaller range of adjustment, but greater resolution.
Included:
- Adapter to connect the reference gauge port on the pump body to the 1/4 NPT male fitting on Fluke 700Pxx Pressure Modules (except 700P29, P30, and P31)
- Adapter to connect the reference gauge port on the pump body to the 1/4 NPT female fitting on the Fluke 700P29, P30, and P31 Pressure Modules
- Adapter to convert the unit under test port to a 1/4 NPT female
- Replacement seal kit
- Instruction sheet
- fluke壓力測試儀 美國福祿克壓力泵
